How To Convert An Installed X64 Windows 7 System, Solved: Install Windows 7 Sp1 X64 On Uefi

The following steps are intended for use by an ITPro in a scenario where they need to convert from Legacy MBR+CSM to UEFI+GPT. Usually this process starts with a system that has Windows 7 x64 installed.

Đang xem: How to convert an installed x64 windows 7 system

For x86 OS systems, see the section in the Firmware WEG FAQ about “What is the dependency on 32-bit vs. 64-bit UEFI?”.

Installed in BIOS mode to Legacy MBR boot disk with CSM enabled, and you know or have checked with the OEM to ensure that the system has the following:

Ability to enable and disable the CSMHas UEFI firmware 2.3.1c or laterThe security features that you are interested in (Secure boot, HVCI, and Credential Guard) have all the correct components already configured on the system.

Note does not currently have a mechanism to convert Legacy MBR boot disks to GPT disks without first wiping or cleaning an existing file system and creating the new file system on the clean disk.

For example, you will need to use Diskpart.exe to clean the existing partition before running the convert GPT command on that disk. The clean command will wipe the entire disk.

Ensure all data is backed up from the primary boot device, and the user or ITPro has confirmed that primary boot device is Disk 0Primary boot device has been completely backed up (any data left on disk will be wiped)Reboot to BIOS (contact the manufacturer for steps to switch BIOS boot mode to UEFI boot mode) aand switch to UEFI+CSMBoot to the USB flash drive that contains x64 WinPEAfter booting into WinPE, at the command prompt:Open Diskpart.exeselect disk 0list parlist VOL convert GPTselect partition 1create par EFI size=800 (mg)format fs=fat32 label=Systemassign letter Screate par MSRlist parexitBack at the command prompt, type in the following:s:BCDboot c:windows /s s: /f UEFI
dir /aYou should see s:EFIReboot and attempt to boot to OS

Verify system is booted in UEFI mode

Use one of the following methods to verify system is booted in UEFI mode.

Xem thêm: Top 10 Trò Chơi Ngày Tết Cổ Truyền, Bé Và Các Trò Chơi Dân Gian Vui Đón Tết


On Windows 10 systems:

Press + to open the Run dialogType Msinfo32 and click OK

The System Summary page will open by default.

Look for the following information:


To run as an administrator, use the following steps:

Press + to open the Run dialogStart typing “System Information”

If System Information is highlighted, hold + and hit , or use your mouse to right-click and select Run as Administrator.

You will be prompted by User Access Control (UAC) with the following message: Do You want this app to make changes to your desktop?


On Windows 7 and later systems:

Start an elevated command promptRun “BCDedit /enum {current}”


If booted from WinPE, use the “/store” switch in BCDedit.exe.If you have UEFI, the path will show Winload.efi.If you have CSM, the path will show Winload.exe as listed in sample output.

Sample output

Windows Boot Loader——————-identifier {current}device partition=C:path WINDOWSsystem32winload.efi


Start an elevated command prompt

Run “notepad c:windowspanthersetupact.log”

Press + for find (or search)

Search for “Callback_BootEnvironmentDetect”

Results would look something like this:

Callback_BootEnvironmentDetect:FirmwareType 1Callback_BootEnvironmentDetect: Detected boot environment: BIOSOr

Callback_BootEnvironmentDetect:FirmwareType 2Callback_BootEnvironmentDetect: Detected boot environment: UEFIYou may need to consult with the OEM for configuration details on your specific system.

Xem thêm: Pokémon Sword And Shield Review, Pokémon Sword And Shield


Using diskpart.exe or Setup to clean or wipe the hard disk drive partition information will all destroy data on the disk. Consult the PC manufacturer concerning factory image recovery methods or data backup options prior to making any of these changes.

Leave a comment

Your email address will not be published. Required fields are marked *